west system 610 cure time

209 Extra Slow Hardener, mixed at a 3:1 ratio with #105 Resin, results in a pot life of 20-25 minutes at 72°F, with 10-15 hours required for a solid cure. When G/flex is used to laminate lightweight fiberglass cloth, the result is a flexible laminate. It is completely compatible with all other WEST SYSTEM products so that it can be used on top of or underneath any 105 Resin-based epoxies, whether cured or uncured. WEST SYSTEM epoxy and hardeners have an excellent shelf-life when stored in sealed containers at room temperature. Additional static mixers are available in packs of 2 and 12. The reliability of WEST SYSTEM Six10 in the self-metering cartridge meets the high standards our customers expect from a WEST SYSTEM product. I have only worked with the West System once, it does have a much faster cure time than the System Three Clear Coat that I used for years. Six10’s cure profile also has some handy features. West System's entire line of epoxy products are explained in this West Marine buyer's guide. Six10 Thickened Epoxy Adhesive combines the strength, reliability and excellent physical properties of a two-part WEST SYSTEM Epoxy with point-and-shoot convenience. WEST SYSTEM 655-610 SIX 10 R/H ADHESIVE. For heavier fabrics, a 105 Resin-based epoxy with its low viscosity should be used to ensure thorough fabric wet out. WEST SYSTEM tutorial on mixing epoxy tips.Find resins and hardeners and other WEST SYSTEMS products at http://www.westmarine.com/. If you have questions about Six10 our Technical Advisors are on hand to answer. Understanding Epoxy’s Cure Time. Six10 can be used for many of the same jobs where a thickened 105 Resin-based epoxy is appropriate, it is a useful adhesive that adds convenience to the versatile WEST SYSTEM product line. It is specifically designed to wet out and bond with wood, fiberglass, reinforcing fabrics and a variety of metals. 99. Stays workable in the static mixer for 42 minutes, making it practical for long or complicated assemblies. If you have questions about Six10 our Technical Advisors are on hand to answer. For heavier fabrics, a 105 Resin-based epoxy with its low viscosity should be used to ensure thorough fabric wet out. 1. Our chemists developed the hardener to provide a long open time but fast thru-cure. This new formulation has a good balance between the elongation and toughness of G/flex® and the strength and stiffness of our 105 Resin-based epoxies. After the same period of time, polyester resin was just over 30% water resistant. Six10 Adhesive provides the same handling properties right out of the cartridge but achieves it with shear thinning, a property that allows the viscosity of the adhesive to become lower when a shear force is applied. time which means the epoxy will stay workable for 42 minutes in the static mixer and before clamping is required—very practical for long or complicated assemblies. A shear force is applied when the epoxy is mixed or spread out over a surface, which causes the viscosity of the Six10 to become lower resulting in a “thinner” consistency. Skip to the end of the images gallery . Mix it with WEST SYSTEM … It was meant to be used in thin films, so its chemistry creates enough heat to push the reaction through without requiring an external heat source to reach a full cure… The molded chambers and passageways accurately control the ratio and prevent the resin and hardener from contacting each other until they are outside the cartridge. Six10 will wet out fabrics up to 12 oz per sq yd. We carefully formulated it for use in many applications where strength and adhesion are important. Our chemists developed the hardener to provide a long open time but fast thru-cure. You can use it with as many materials as possible including wood, metals and composites. Neighbors App Real-Time … If you need more time, here is a simple … Epoxy temperature: higher temperatures mean faster cure speeds Controlling cure time in warm and cold conditions. 105 Resin is paired with one of four hardeners depending on the user’s needs for working time … Six10 has a viscosity high enough to resist sagging but can still saturate and wet-out a surface without pre-coating, thanks in part to shear thinning. Size: 190 ml SKU: WSY-610 Category: Maintenance > West System … An epoxy’s open time and overall cure time govern much of the activity of building and repairing with epoxy, and hardener selection is crucial to determining open time and cure time. 209 Extra Slow Hardener will not cure properly at low temperatures but provides more working time at higher temperatures. If you use a stiff plastic spreader, Six10 can wet out any fiberglass fabric lighter than 12 oz per square yard as a result of its shear thinning characteristics. This shear-thinning property enables Six10 to be easily dispensed out of the coaxial cartridge and through the static mixer and then tooled smoothly into a fillet that won’t sag during the cure cycle. The self-metering coaxial cartridge dispenses a gap-filling structural epoxy that bonds to … To use Six10 Adhesive, replace the retaining nut and plug on the West … WEST SYSTEM Six10 has a modulus slightly lower than a 105 Resin epoxy, making it appropriate for many applications where a filled a 105 Resin-based epoxy would be used. When G/flex is used to laminate lightweight fiberglass cloth, the result is a flexible laminate. West System 206 & 205 fast; MAS slow & fast; System Three slow, medium and fast; Raka 350 & 610 fast; With the rest you are stuck on one speed. There are four WEST SYSTEM hardeners. With a pot life of 42 minutes, WEST SYSTEM Six10 will provide over an hour of working time in a thin film but will achieve an initial cure in just 5–6 hours. If you use a stiff plastic spreader, Six10 can wet out any fiberglass fabric lighter than 12 oz per square yard as a result of its shear thinning characteristics. Estimating Epoxy Coverage for Fabric Application, Fiberglass Boat Repair & Maintenance (pdf), Common Mistakes in Fiberglass Repair (Webinar), The Gougeon Brothers On Boat Construction book, Health Effects from Overexposure to Epoxy, Call from outside the U.S.A. 1-989-684-7286, Understanding Six10 Epoxy Adhesive Properties, It separates the resin and hardener for long term storage, It accurately meters the proper 2:1 resin/hardener ratio. We cannot warranty decanted products because they may be diluted, contaminated, or not actually WEST SYSTEM products. With a pot life of 42 minutes, WEST SYSTEM Six10 will provide over an hour of working time in a thin film but will achieve an initial cure in just 5–6 hours. Combines the strength and reliability of a two-part WEST SYSTEM epoxy with point-and-shoot convenience. Six10® has a working time of 42 minutes (within the static mixer) so it can be used for a wide variety of projects. Hardener Selection Controls Cure Time. The time it takes for this transformation is the cure time. The 105 Resin/206 Slow Hardener has a pot life of 30-40 minutes at 70°F. $23.99 $ 23. As it cures, the epoxy passes from the liquid state, through a gel state, before it reaches a solid state. This innovative container provides many useful features: The cartridge works by utilizing the movement of the piston to simultaneously dispense the resin and hardener from separate chambers. The Six10 cartridge holds 190ml of resin and hardener. When fully cured, WEST SYSTEM … 1-16 of 53 results for "west system 610" Price and other details may vary based on size and color. With the 600 Static Mixer attached to the Six10 Epoxy Adhesive cartridge, it’s easy to lay down a bead of thickened epoxy adhesive right where you need it. Six10’s cure profile also has some handy features. Cure time is faster at warm temperatures and slower in cool temperatures. Cure to a solid state: 10 to 15 hours Cure to maximum strength: 1 to 4 days Minimum recommended temperature: 60°F (16°C) The physical properties of WEST SYSTEM Six10 were developed to ensure good adhesion in many applications. 3. It separates the resin and hardener for long term storage, It accurately meters the proper 2:1 resin/hardener ratio. While you’re working, adhesive in the mixer will eventually begin to cure. It is completely compatible with all other WEST SYSTEM products so that it can be used on top of or underneath any 105 Resin-based epoxies, whether cured or uncured. 2. WEST SYSTEM® Six10 is a two-part, pre-thickened epoxy adhesive formulated with properties that make it perfect for many adhesive applications. An additional characteristic of Six10’s cure profile is that sufficient working time is maintained in warm temperatures. As we discussed in Epoxyworks 25, G/flex was formulated to be flexible enough to work in many unique situations but 105 Resin-based epoxies are still recommended for applications where a stiff laminate is required. Six10 has a viscosity high enough to resist sagging but can still saturate and wet-out a surface without pre-coating, thanks in part to shear thinning. If this is the first time you have used WEST SYSTEM epoxy, begin with a small test batch to get the feel for the mixing and curing process, before applying the mixture to your project. Mix with one of four WEST SYSTEM Hardeners. The physical properties of WEST SYSTEM Six10 were developed to ensure good adhesion in many applications. Six10 will create a fiberglass laminate much closer to 105 Resin epoxy laminate properties. WEST SYSTEM® Six10 Thickened Epoxy Adhesive is packaged in a specially designed, self-metering cartridge. The speed with which the water resistance of polyester degraded also appeared to increase over time. With the 600 Static Mixer attached to the Six10 cartridge, it’s easy to lay down a bead of thickened epoxy adhesive right where you need it. WEST SYSTEM initially developed its 105 Resin-based epoxy system as a laminating epoxy. This feature makes the product convenient for performing small fiberglass boat repairs. Each tube of Six10 comes equipped with a static mixing wand. As we discussed in Epoxyworks 25, G/flex was formulated to be flexible enough to work in many unique situations but 105 Resin-based epoxies are still recommended for applications where a stiff laminate is required. The charts above illustrate the properties of our G/flex and 105 Resin-based epoxies compared to WEST SYSTEM Six10 and illustrates how Six10 fits in nicely between the high strength of 105 Resin-based combinations and the toughness of G/flex. Our technical advisors and chemists extensively tested the performance of the cartridge and 600 Static Mixer to ensure accurate metering and thorough mixing of the Six10 resin and hardener. As the epoxy is … 600-2 Pack of Static Mixers for Six10 Epoxy, 2 ea. Picture may differ from product, check the description and confirm your part numbers. All adhesives rely on good surface “wet out” and saturation to achieve a good bond to the substrate. WEST SYSTEM Six10 is a two-part, pre-thickened epoxy adhesive formulated with properties that make it perfect for many adhesive applications. When you are done applying or mixing Six10 and it is no longer being worked, or “sheared,” it will start to increase in viscosity and develop a thicker consistency. The consistency and of Six10 Adhesive is perfect for fillets. The molded chambers and passageways accurately control the ratio and prevent the resin and hardener from contacting each other until they are outside the cartridge. The epoxy is pre-thickened to prevent sagging during the curing process. Compared to other ready-to-dispense adhesives, its particular … Partial cure time at 70°F is 5-7 hours. Start with 105 Resin, the basic ingredient of all WEST SYSTEM epoxy compounds. Our chemists developed the hardener to provide a long open time but fast thru-cure. Incudes one 600 Static Mixer. Use WEST SYSTEM 205 Fast Hardener. ... TotalBoat Thixo Fast Cure 2:1 Epoxy System. The consistency and of Six10 Adhesive is perfect for fillets. The tube comes with a static mixer that lets you lay down a bead of thickened epoxy with any standard caulking gun. It has a minimum recommended working of temperature of 60°F. 205 Hardener has been designed with a polyamine system … It reaches an initial cure in 7 to 10 hours and full cure in 24 hours. 4.4 out of 5 stars 20. It was in a lab and under very specific conditions but WEST SYSTEM 105 Epoxy Resin® with 205 Fast Hardener® came out on top, demonstrating more than 80% water resistance at 6 weeks of continued moisture exposure. The charts above illustrate the properties of our G/flex and 105 Resin-based epoxies compared to WEST SYSTEM Six10 and illustrates how Six10 fits in nicely between the high strength of 105 Resin-based combinations and the toughness of G/flex. The self-metering coaxial cartridge dispenses a gap-filling structural epoxy that bonds tenaciously to wood, metals, fiberglass and concrete. Our technical advisors and chemists extensively tested the performance of the cartridge and 600 Static Mixer to ensure accurate metering and thorough mixing of the Six10 resin and hardener. 1. With a pot life of 42 minutes, WEST SYSTEM Six10 will provide over an hour of working time in a thin film but will achieve an initial cure in just 5–6 hours. Six10 Epoxy Adhesive is readily tooled into a fillet. Epoxy bonds incredibly well to woods, fiberglass materials, metals and concrete, but it is typically a two part system … This innovative container provides many useful features: The cartridge works by utilizing the movement of the piston to simultaneously dispense the resin and hardener from separate chambers. An additional characteristic of Six10’s cure profile is that sufficient working time is maintained in warm temperatures. We carefully formulated it for use in many applications where strength and adhesion are important. The hardener provides a long open time but has fast thru-cure. It can be easily tooled into a non-sagging fillet or used to wet out light to moderate reinforcing fabrics like fiberglass. The long working time with fast thru-cure and unique shear thinning are additional characteristics formulated into Six10 that contribute to its ease of use. CAUTION! 206 Slow Hardener is a low-viscosity mixture of polyamines. The shear thinning property also enables Six10 to be used for wetting out light to moderate weight reinforcing fabrics such as fiberglass and carbon fiber. Each tube of Six10 comes … Add one of six WEST SYSTEM … Compared to other ready-to-dispense adhesives, its particular physical properties make it ideal for stitch and glue boat construction, fiberglass laminate repair and general bonding. 600-12 Pack of Static Mixers for Six10 Epoxy, 12 ea. The long open time also means that the epoxy will stay workable in the static mixer for 42 minutes, which is very practical for long or complicated assemblies. Open time and cure time govern much of the activity of building … WEST SYSTEM Six10 has a modulus slightly lower than a 105 Resin epoxy, making it appropriate for many applications where a filled a 105 Resin-based epoxy would be used. A WEST SYSTEM customer offers a close-up demonstration of the Six10 Static Mixing Wand at work. Our chemists accomplished this formulation by using an ingenious filler package in both the resin and hardener components. The shear-thinning property also enables Six10 to be used for wetting out light to moderate weight reinforcing fabrics such as fiberglass and carbon fiber. With a pot life of 42 minutes, WEST SYSTEM Six10 will provide over an hour of working time in a thin film but will achieve an initial cure in just 5–6 hours. A shear force is applied when the epoxy is mixed or spread out over a surface, which causes the viscosity of the Six10 to become lower resulting in a “thinner” consistency. This feature makes the product convenient for performing small fiberglass boat repairs. The WEST SYSTEM User Manual and Product Guide is available upon request. With the 600 Static Mixer attached to the Six10 cartridge, it’s easy to lay down a bead of thickened epoxy adhesive right where you need it. The consistency of Six10 Thickened Epoxy Adhesive is perfect for fillets. The RAKA I use now is more like the West as far as cure … The hardener provides a long open time but has fast thru-cure… This will demonstrate the hardener's open time … It is ideal for stitch and glue boat … With the 105 System, users can blend resins, hardeners, fillers and additives to get the right combination for their project’s requirements. Additional static mixing wands are available in sets of two (product number 600-2) or twelve (product number 600-12). Liquid—Open time : Also known as working time or wet lay-up time, is the portion of the cure time… All adhesives rely on good surface “wet out” and saturation to achieve a good bond to the substrate. Six10 stays workable in the static mixer for 42 minutes, making it practical for long or complicated assemblies. The hardener provides a long open time but has fast thru-cure. Experienced WEST SYSTEM users are familiar with the handling characteristics of 105 Resin-based epoxy thickened with 406 Colloidal Silica Filler that allows it to be non-sagging, yet trowel easily. Six10 stays workable in the static mixer for 42 minutes, making it practical for long or complicated assemblies. Call our Technical Staff toll-free: 866-937-8797 (Weekdays 9:00 AM to 5:00 PM EST), Outside of the U.S.A., call 1-989-684-7286. Select a hardener for its intended use and for the cure speed best suited for your job in the temperature range in which you are working. You should have about 42 minutes at 70°F before you need to dispense more epoxy. Includes 4 ounces of resin and 4 ounces of hardener. Two-part strength in caulking gun convenience. The hardener provides a long open time but has fast thru-cure. Our chemists accomplished this formulation by using an ingenious filler package in both the resin and hardener components. Six10’s shear thinning properties make it “thinner” as it’s worked. Open time … 650 G/flex Resins should be paired with comparable size 650 G/flex Hardeners. Hardener cure speed: ensure you have enough working time. Six10 will create a fiberglass laminate much closer to 105 Resin epoxy laminate properties. West Systems 610 Six 10 R/h Adhesive. Just call 866-937-8797 toll-free. Always buy WEST SYSTEM products in original, sealed factory containers. WEST SYSTEM® Six10 Thickened Epoxy Adhesive is packaged in a specially designed, self-metering cartridge. When you are done applying or mixing Six10 and it is no longer being worked, or “sheared,” it will start to increase in viscosity and develop a thicker consistency. The long open time also means that the epoxy will stay workable in the static mixer for 42 minutes, which is very practical for long or complicated assemblies. This shear thinning property enables Six10 to be easily dispensed out of the coaxial cartridge and through the static mixer and then tooled smoothly into a fillet that won’t sag during the cure cycle. It is useful in a majority of bonding situations, and at lower temperatures. WEST SYSTEM epoxies are versatile. Six10 will wet out fabrics up to 12 oz per sq yd. Six10’s cure profile also has some handy features. 205 Fast Hardener is a medium-viscosity epoxy curing agent. The reliability of WEST SYSTEM Six10 in the self-metering cartridge meets the high standards our customers expect from a WEST SYSTEM product.—Excerpted from Understanding Six10 Epoxy Adhesive Properties by Jeff Wright, Epoxyworks 27. None of the epoxies were mixed so the test is valid only … 205 Fast Hardener produces a rapid epoxy cure that develops physical properties quickly at room temperature. Our chemists developed the hardener to provide a long open time but fast thru-cure. Six10 can be used for many of the same jobs where a thickened 105 Resin-based epoxy is appropriate, it is a useful adhesive that adds convenience to the versatile WEST SYSTEM product line. It is normally used when extended time … Just call 866-937-8797 toll-free. Six10 Adhesive provides the same handling properties right out of the cartridge but achieves it with shear thinning, a property that allows the viscosity of the adhesive to become lower when a shear force is applied. Six10’s cure profile also has some handy features. Each has a different cure time and an ideal temperature cure … Experienced WEST SYSTEM users are familiar with the handling characteristics of 105 Resin-based epoxy thickened with 406 Colloidal Silica Filler that allows it to be non-sagging, yet trowel easily.

Dell G3 15 Gaming Laptop Specs, George's Bloody Mary Mix Review, Tequila Soaked Fruit, On The Border Schaumburg, Playstation Gold Wireless Headset White, Murad Rapid Age Spot And Pigment Lightening Serum Canada, Construction Management Associate's Degree Vs Bachelor's, Zebra Seahorse Habitat, Australian Bass Recipe, George's Bloody Mary Mix Review, Cerave Facial Moisturizing Lotion Spf 25 Review, Smash Ultimate Mario Spike,

Leave a Comment